Note: Position brake caliper as illustrated to pre-bleed. Re-install in their original position to prevent uneven braking! If you go through each part and line of these manuals, then you will understand everything in these guides very simply. All pages are printable, so print off what you need and take it with you anywhere. If piston is difficult to move, use a 13 mm open end wrench on flats arrow A provided for this purpose. Haynes writes every book based on a complete teardown of the vehicle. Before pressing the piston back, remove some brake fluid from the reservoir with a bleeder bottle.
If necessary pull both sections firmly apart onto stop or press together. This manual provides the most reliable information to perform the job. Note: Place a piece of wood in the recess to prevent damaging the piston. If scoring can be felt, replace the complete steering gear - Clean toothed rod remove old grease in tooth. If complaints are received determine cause with the help of pressure tests, leakage test and troubleshooting programs. Kool Vue specializes in producing mirrors for all vehicle makes and models; Our mirrors go through rigorous weather, swing, and vibration testing to make sure you receive the highest quality mirrors. Front sub-frame M12 x 1.
Note: Chamfer on inner diameter of ball hub splines must face the contact shoulder on the drive shaft. Volkswagen Passat The Volkswagen Passat is a large family car from German automaker Volkswagen and was introduced in 1973. The sealing lip - arrow- points toward tool - Drive sealing ring into stop 1 - Sealing ring. Note: Hold piston in front of caliper housing. Make sure plier jaws seat in grooves of clamp arrows -B- - Tension clamp by using torque wrench to turn spindle keep pliers at right angle to shaft. This product will play in a virtual version of Windows via VirtualBox free.
Note: This installation position tolerance is also valid for the left drive shaft transmission end boot polyester elastomer version. A must read manual that is written from hands-on experience based on a complete teardown of the vehicle. We learn the best ways to do a job and that makes it quicker, easier and cheaper for you. No more greasy Haynes type manuals. Anyway, every manual or guide must be according to your vehicle name, year of manufacturing and official model. Installing Note: Hydraulic units supplied as replacement parts are already filled with hydraulic fluid and bled. See product for application and installation details.
This Passat Workshop Manual is a complete Windows and Apple Mac based Service Repair Information System. Its derivatives have been badged variously as the Dasher, Quantum, Magotan, Carat, Corsar and Santana, through six generations. Specification: 85 - 95 bar 1232 - 1377 psi Note: If the reading is higher or lower than specified replace pump. Note: Grease all mountings before installing with G 000 602 grease. Removing left-side drive axle - Set up engine support bridge.
For a satisfactory and successful repair, the greatest care, safety and proper tools are required. Note: The protective seal outer sealing lip will then locate in the piston groove. Steering gears that are damaged by an accident must be replaced For a satisfactory and successful repair, the greatest care, safety and proper tools are required. New brake calipers are filled with brake fluid and are pre-bled. This simple to use menu driven repair manual offers all the main functions seen below to service or repair your car, including Strict Maintenance Operations using a step by step process. Make sure that the blades of the pliers lie in the corners arrow -B- of the clamp. These must be installed pointing forward, otherwise damage will occur to the suspension strut piston rod.
Pull off protective foil and stick onto joint. Ib New belts, 7 Nm 62 in. Page 3 of 5 45-3 Thoroughly clean all unions and the adjacent areas before loosening, do not use aggressive cleaning agents such as brake cleaner, petrol, thinners or similar. Tightening torque: 10 Nm 7 ft lb Fig. Volkswagen also got involved in rallying and achieved great success throughout the years — including a dominant stint in the World Rally Championship. . So browse around our great selection of car parts and let's help with that auto repair or car upgrade! Removing and installing suspension strut at body Page 42-4 Tightening torque -A-: 65 Nm 48 ft lb Note: Support control arm otherwise damage may occur to.
Welding and straightening of the axle beam is not permissible. Note: Do not adjust with brake pedal depressed, therefore observe the following sequence: - Read off figures. Fidanza Performance is a renowned manufacturer that specializes in performance flywheels, clutches, cam gears and other top-quality driveline parts. Pull foam rubber sleeve off connector, if installed. Therefore note the following points: Install oil seal and grease cap as shown.
The continued line must pass through the center of hole arrow. For anti-theft coded radios, first make sure that the radio code is available. Note: The 6 balls of each joint belong to one tolerance group. The company sells its vehicles worldwide and is responsible for popular models like the Golf, Jetta, Beetle, Passat and Transporter. Only use stub axles with 6 mounting holes.