This can help loosen any stuck pins or springs. Generally, most vehicles have a split-plastic housing that covers the steering column and ignition lock assembly. Apply pressure to the steering wheel. Your car has a steering lock that clicks into place when you take the car key out of the. Do all modification at your own risk. Once done, insert the key and turn it back and forth gently to work the lubricant in. I live in a dusty place and I work in the dirt so my problem is probably not all that common.
Be careful not to spray too much into the key hole. Call your usual car service people and ask them if they'd mind checking it out for you. The steering wheel is locked in place using a pin on one side. Ignition tumblers experience a lot of mechanical movement and force over time which can cause them to fail, preventing the steering wheel from unlocking. Keep trying to gently turn the key and the wheel at the same time until the wheel unlocks. There have been times that the ignition lock has to be drilled out and replaced.
I then took shop air preasure and blew out the lock cylinder,the key turns now, so the lock clinder could be replaced, but I feel that it was the pocket fuzz creating the problem, so if its not broke dont fix it. If your steering wheel is locked, then one of those two directions will be very solid and one direction will be a little springy wheel wants to spring back. If you found this page helpful we would really appreciate any donations you could send us. I have taken the airbag out before, but cannot get to both clips because I cannot turn the steering wheel. Ignition assemblies are easily replaced in most vehicles and can be done at home by most hobby mechanics. This isn't unusual in higher end vehicles, which frequently use more complex electronic ignition systems.
Remove this plastic cover by first adjusting the tilt-wheel to its lowest position and then removing the fasteners holding the cover in place. The main purpose of a locked wheel is to prevent vehicle movement when there is no key, or if the wrong key is inserted into the ignition. . From the experimenting I have done with the old part, the pin does not drop on its own until the key is turned. There are three components to be aware of: Component 1: Steering wheel.
I assume I just need a new ignition switch? The instructions below are for every year, make and model vehicle ever manufactured. Below are the two most common problems associated with the ignition lock cylinder and the key not turning. No one but yourself is liable for mishaps. Would physically shaking the truck release the locking mechanism? Occasionally, because of this lock, the steering wheel can get stuck, which in turn means the vehicle key also becomes stuck and cannot move to release it. Repeat the process a few times to try to move any debris that may be caught in the cylinder. New ignition switches come pre-lubed from the factory ready to install.
Some vehicles do not allow the key to turn unless the vehicle is in either park or neutral. Ensure the key is not bent or damaged. This can result in an inability to turn the ignition on. To clean, use electrical cleaner or compressed air, and follow the precautions and instructions on the can. Reason 3 of 3: Ignition lock cylinder issues Also known as a key cylinder, the ignition lock cylinder is another area that could be causing issues with a key turning over.
Is there a way to get it off with only disengaging the clip on one side? Narrow down the cause of the issue by attempting a number of methods before having the vehicle towed to a repair facility. You may still be able to engage the pins needed to start the vehicle by inserting the key in all the way, then pulling it back out slightly. Again, this solution only applies to vehicles with a traditional ignition key, meaning a metal key that actually inserts into an ignition switch and turns to start the car. Also, if your car has a starter button, but your steering wheel seems stuck, you will need to go to the repair shop because it's most likely an electronic issue rather than a simple fix. If that is not helping then first turn steering wheel to right and try removing the key, or next turn steering wheel to left and see if you can remove the key. It feels like the pin that locks the steering wheel in place will not move when you stick the key in and try to turn it.
Thanks, -J Many, many people told me it was because of the locking steering wheel, which I knew was not the case. Daughter drove it to work while we were gone and said when she tried to go home the key would not turn at all. Ford vehicles such as Focus, Contour, Cougar and Mystique tend to stop turning because of ignition wear, all other Ford vehicles tend to be or. The wafers have small points on them which ride along the grooves of the key. This is a very common and known issue with Honda. Ensure the vehicle is in park.